扬州SKF轴承6212/C3小孔润滑的配合安装

扬州SKF轴承的正确安装直接影响轴承使用时的精度、寿命和性能。因此，扬州SKF轴承设计和装配部门应根据操作标准对轴承安装进行全面的研究。操作标准项目通常如下：

The correct installation of SKF bearings in Yangzhou directly affects the accuracy, life and performance of bearings when used. Therefore, the SKF bearing design and assembly department of Yangzhou should conduct a comprehensive study on the bearing installation according to the operation standard. The operating standard items are usually as follows:

清洗扬州SKF轴承及相关零件

Cleaning the SKF bearing and related parts in Yangzhou

检查相关零件的尺寸和精度

Check the size and accuracy of the related parts

安装

install

安装后检查扬州SKF轴承

Check Yangzhou SKF bearing after installation

填料润滑剂

Filler lubricants

希望扬州SKF轴承包装在安装时打开。润滑脂润滑时，轴承不清洗，直接用油脂填充。当油被润滑时，不必清洗它。然而，仪器或高速扬州SKF轴承用清洁油清洗，以去除应用于轴承的防锈剂。除锈剂易生锈，不能随意放置。

It is hoped that the Yangzhou SKF bearing packaging will be opened at the time of installation. When lubricating grease is lubricated, bearings are not cleaned and filled directly with grease. When the oil is lubricated, it is not necessary to clean it. However, the instrument or high speed Yangzhou SKF bearing is cleaned with clean oil to remove rust inhibitors applied to bearings. Rust remover is easy to rust and can not be placed at will.

此外，扬州SKF轴承润滑脂不直接清洗和使用。

In addition, Yangzhou SKF bearing grease is not directly cleaned and used.

轴承的安装方法，由于轴承的结构、协调、条件不同，一般由于轴的转动，所以内圈需要过盈配合。圆柱孔轴承通常用压力机压紧或加热。锥形孔直接固定在锥形轴上或装有紧套。

Bearing installation method, due to the bearing structure, coordination, different conditions, generally due to the rotation of the shaft, so the inner ring need interference fit. Cylindrical bore bearings are usually pressed or heated by a press. The tapered holes are directly fixed on the conical shaft or equipped with tight sleeves.

当安装在扬州SKF轴承座上时，经常采用间隙配合。当外圈受到干扰时，通常用压力机压或冷却。当干冰被用作冷却剂和冷缩装置时，空气中的水凝结在轴承表面上。因此，需要采取防锈措施。

When installed on the SKF bearing block in Yangzhou, the gap fit is often used. When the outer ring is disturbed, it is usually pressed or cooled with a press. When dry ice is used as coolant and cold shrinkage device, the water in the air condenses on the surface of the bearing. Therefore, anti rust measures need to be taken.

小型扬州SKF轴承广泛应用于压力机上。按压内圈上的垫圈并将其压入内圈的末端，靠近肩部。外圈安装在垫圈上安装内座圈，会在跑道上造成压痕或压缩，因此严禁。

Small Yangzhou SKF bearings are widely used in presses. Press the washer on the inner ring and press it into the end of the inner ring, near the shoulder. The outer ring is installed on the washer to install the inner race, which will cause indentation or compression on the runway, so it is strictly prohibited.

文章来自：扬州SKF轴承 www.wh-skf.com

The article comes from: Yangzhou SKF bearing www.wh-skf.com

文章来自：扬州INA轴承 www.ina-china.cn

The article comes from: Yangzhou INA bearing www.ina-china.cn

文章来自：扬州NSK轴承 www.klbbearings.com

The article comes from: Yangzhou NSK bearing www.klbbearings.com

QQ：524085168  

电话：0510-81207777

手机：13311666672