点击图片查看原图
避免失败的风险其实很简单。使用南京SKF轴承时，公司必须进行全面、专业的测试。在轴承运行数据不稳定的情况下，可以及时发现各种可能的故障，达到预防的目的。掌握早期预防和技能可以降低公司一半以上的成本，这对于降低企业使用成本具有重要意义。
Avoiding the risk of failure is actually very simple. When using Nanjing SKF bearings, the company must conduct a comprehensive and professional test. In the case of unstable bearing operation data, various possible faults can be found in time to achieve the purpose of prevention. Mastering early prevention and skills can reduce the cost of more than half of the company, which is of great significance to reduce the cost of enterprise use.
只要南京SKF轴承失效，基本数据将不可避免地在很宽的范围内变化。使用一段时间后，测量的具体尺寸和内部间隙，如果数据间隙相对较大，也就是说轴承可能会失效。在这一点上，有必要对专业设备的故障诊断和生发状态进行测试。
As long as the SKF bearing in Nanjing fails, the basic data will inevitably change in a wide range. After a period of use, the measured specific size and internal clearance, if the data gap is relatively large, that is, the bearing may fail. At this point, it is necessary to test the fault diagnosis and germinal state of professional equipment.
由于许多南京SKF轴承故障突然失效，很难及时发现和调查。此时，企业需要统计统计前后的各项运行数据，及时发现异常数据并准确检测，只有通过努力工作，企业才能远离各种故障的威胁，保持安全稳定的运行。
Due to the sudden failure of many SKF bearings in Nanjing, it is difficult to detect and investigate in time. At this time, enterprises need to statistics before and after the operation of data, timely detection of abnormal data and accurate detection, only through hard work, enterprises can be far from the threat of various faults, and maintain a safe and stable operation.
有丰富的经验和错误的判断是有用的。通过对运行数据的实证分析，可以发现各种潜在的轴承故障，从而保证轴承生产对故障的影响。
It is useful to have rich experience and erroneous judgement. Through the empirical analysis of operation data, various potential bearing faults can be found, thus ensuring the impact of bearing production on the faults.
以不正确的方式拆卸振动轴承可能损坏内部南京SKF轴承，例如当进入或重新安装设备时。因此，在打开振动筛的情况下必须非常小心和严格，轴承轴必须得到适当的支撑，否则强制拆卸很可能损坏南京SKF轴承。
Improper removal of vibration bearings may damage the internal Nanjing SKF bearings, such as when entering or reinstalling equipment. Therefore, in the case of opening the shaker must be very careful and strict, bearing shaft must be properly supported, otherwise mandatory demolition is likely to damage the Nanjing SKF bearing.
首先是外部爆破。拆下过盈配合外圈时，应事先在外壳周围设置一定数量的外圈压力螺钉，拆卸时应拧紧螺钉。这些螺钉孔通常覆盖有可拆卸的轴承，如盲塞、振动筛、圆锥滚子轴承等，并且在壳体的肩部上有许多凹口，用于去除南京SKF轴承垫圈的垫圈或轻轻吸去以去除垫圈。
The first is external demolition. When removing the interference fit outer ring, a certain number of outer ring pressure screws should be set around the outer shell in advance, and the screws should be tightened when removing. These screw holes are usually covered with removable bearings such as blind plugs, vibrating screens, tapered roller bearings, etc., and there are many notches on the shoulders of the housing used to remove the gaskets of the Nanjing SKF bearing washers or to gently suck them away to remove the gaskets.
然后拆下振动筛的圆柱孔轴承。内环可以通过最新的压力很容易地去除。但这一次，我们要注意内环的内部张力。
Then remove the cylindrical bore bearing of the vibrating screen. The inner ring can be easily removed by the latest pressure. But this time, we should pay attention to the internal tension of the inner ring.
采用振动法去除大型振动筛的轴承套圈。油压力通过轴上的油孔提供，以便于拉伸。对于大的宽度，可以使用液压拆卸和拉动夹具。NJ内圈和NJ圆柱滚子南京SKF轴承可以通过感应加热除去。简单地说，局部加热时间和内环后的延伸方法被加热。
Vibration method is adopted to remove the bearing ring of large vibrating screen. The oil pressure is provided through the oil holes on the shaft for easy stretching. For large width, hydraulic dismantling and pulling clamps can be used. NJ inner ring and NJ cylindrical roller bearing of Nanjing SKF can be removed by induction heating. Simply speaking, the local heating time and the extension method after the inner ring are heated.
最后拆卸锥形孔轴承。当用固定套筒去除较小的零件时，内圈可以用轴块固定，螺母旋转几次，用锤子将垫子击倒。
Finally remove the tapered bore bearing. When smaller parts are removed with a fixed sleeve, the inner ring can be fixed with a shaft block, the nut rotates several times, and the cushion is knocked down with a hammer.
文章来自：南京SKF轴承 www.wh-skf.com
The article is from: Nanjing SKF bearing www.wh-skf.com
文章来自：南京INA轴承 www.ina-china.cn
The article is from: Nanjing INA bearing www.ina-china.cn
文章来自：南京NSK轴承 www.klbbearings.com
The article is from: Nanjing NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672
会员未认证
