镇江SKF轴承6100阐释毁坏的环境下运行

为了检查镇江SKF轴承的损坏，可以发现，在大多数情况下，轴承会造成损坏。一般来说，只要轴承疲劳造成的损坏三分之一来自于平滑度差，三分之一来自于对进入轴承或设备的污染物的不当处理。然而，这些违规行为是无关紧要的，性能轴承都是全机械化的，须配合一定的时间和严格的位置，即使用高性能轴承，如果应用不当，也不能达到预期的功能后果，而且容易损坏。它有它。

In order to check the damage of Zhenjiang SKF bearing, it can be found that in most cases, the bearing will cause damage. Generally speaking, as long as one third of the damage caused by bearing fatigue comes from poor smoothness, one third comes from improper treatment of pollutants entering the bearing or equipment. However, these violations are irrelevant, performance bearings are fully mechanized, must be matched with a certain time and strict location, even with high-performance bearings, if improper application, can not achieve the desired functional consequences, and easy to damage. It has it.

因此，轴承应用应注意以下几点：

Therefore, bearing applications should pay attention to the following points:

首先，保持镇江SKF轴承及其周围环境的清洁将增加轴承的磨损、振动和音乐，甚至小的、看不见的灰尘轴承。

First, keeping Zhenjiang SKF bearings and their surrounding environment clean will increase bearing wear, vibration and music, and even small, invisible dust bearings.

其次，使用设备进行强力冲压，不允许锤子间接冲击镇江SKF轴承，不允许压力过大。

Secondly, the use of equipment for strong stamping, not allow hammer indirect impact Zhenjiang SKF bearing, not allow excessive pressure.

第三，使用适当的设备将物体放置在异物中，即使它们防止布料和短纤维。

Third, use appropriate equipment to place objects in foreign objects, even if they prevent cloth and short fibers.

第四，防止手轴承、汗液腐烂，然后高品质的矿物油画在旱季和夏季运行，特别注意防锈。然而，在某些特殊情况下，传统的计算方法可以应用于镇江SKF轴承的计算，以获得更好的结果，特别是在轻载的前提下。事实上，这些额外的操作是以当旋转表面(轨道和旋转部件)是用于分离和识别污染物的有用的光滑膜时发生外力损伤为前提的。

Fourth, prevent hand bearings, sweat decay, and then high-quality mineral oil paintings in the dry season and summer operation, with special attention to rust prevention. However, in some special cases, the traditional calculation method can be applied to the calculation of Zhenjiang SKF bearing to obtain better results, especially under the premise of light load. In fact, these additional operations are premised on the occurrence of external force damage when the rotating surface (orbits and rotating parts) is a useful smooth membrane for separating and identifying contaminants.

由于许多轴承故障处于紧急状态，因此很难实时建立和停止调查。此时，它是企业应用程序负载停止运行数据，每次必要的统计，并实时检测数据。只要他们尽大努力，就可以清理掉各种故障的威胁，使轴承稳定运行。

Because many bearing failures are in a state of emergency, it is difficult to establish and stop the investigation in real time. At this point, it is enterprise application load stop running data, each time necessary statistics, and real-time detection of data. As long as they make great efforts, they can clear up all kinds of faults and keep the bearings running steadily.

文章来自：镇江SKF轴承 www.wh-skf.com

The article is from: Zhenjiang SKF bearing www.wh-skf.com

文章来自：镇江INA轴承 www.ina-china.cn

The article is from: Zhenjiang INA bearing www.ina-china.cn

文章来自：镇江NSK轴承 www.klbbearings.com

The article is from: Zhenjiang NSK bearing www.klbbearings.com

QQ：524085168

电话：0510-81207777

手机：13311666672